 |
 |
|
||
 |
||||
Duplex Printing With the Auto Duplexer
For Windows
You can perform automatic duplex printing with the Auto Duplexer by following these steps.
Note:|
You can perform automatic duplex printing with plain paper, Epson Premium Ink Jet Plain Paper, and Epson Bright White Ink Jet Paper in A4, Letter, and B5 sizes.
If the ink runs low during automatic duplex printing, the printer stops printing and the ink needs to be replaced. When ink replacement is complete, the printer starts printing again, but there may be some missing parts in your print out. If this happens, print the missing parts again.
|
 |
Access the printer settings.
|
 |
Click the Maintenance tab, and then select Printer and Option Information.
|
 |
Make sure the Auto Duplexer Installed check box is selected, and click OK.
|
 |
Click the Main tab, and then select one of the following Quality Option settings:
|
Draft for rough drafts with reduced print quality
Text for text-only pages
Text & Image for higher quality pages with text and image
Photo for good quality and speed
Best Photo for the best print quality
 |
Select Rear Tray, Front Tray, or Automatic as the Source setting.
|
 |
Select Plain Paper as the Type setting.
|
 |
Select A4 210 x 297 mm, Letter 8 1/2 x 11 in, or B5 182 x 257 mm as the Size setting.
|
 |
Select Portrait (tall) or Landscape (wide) to change the orientation of your print out.
|
 |
Click the Page Layout tab, and then select the Duplex Printing check box and the Auto radio button. If you want to create a folded booklet, select the Folded Booklet check box.
|
 |
Click Margins to open the Margins window.
|
 |
Specify the edge of the paper where the binding will be placed. You can choose Left, Top, or Right.
|
 |
Choose cm or inch as the Unit setting. Then specify the width of the binding margin. You can enter any width from 0.3 cm to 3.0 cm, or from 0.12 inches to 1.18 inches.
|
Note:|
The actual binding margin may be different from the specified settings depending on your application. Experiment with a few sheets to examine actual results before printing the entire job.
|
 |
Click OK to return to the Page Layout window. Then click OK to save your settings.
|
 |
Click the Adjust Print Density button to open the Print Density Adjustment window.
|
Note:|
If you are printing high-density data, such as photos or graphs, we recommend making the settings in the Print Density Adjustment window.
|
 |
Select one of the Select Document Type settings. This automatically adjusts Print Density and Increased Ink Drying Time.
|
 |
Click OK to return to the Page Layout window.
|
 |
Make sure all of the settings are correct, and then click OK.
|
 |
Load paper into the rear feeder or front paper cassette, then send the print job from your application.
|
For Mac OS X
You can perform automatic duplex printing with the Auto Duplexer by following these steps.
Note:|
You can perform automatic duplex printing with plain paper, Epson Premium Ink Jet Plain Paper, and Epson Bright White Ink Jet Paper in A4, Letter, and B5 sizes.
If the ink runs low during automatic duplex printing, the printer stops printing and the ink needs to be replaced. When ink replacement is complete, the printer starts printing again, but there may be some missing parts in your print out. If this happens, print the missing parts again.
This feature is available only with Mac OS X 10.3 or later.
|
|
Access the EPSON Printer Utility2 dialog box.
|
|
Click the Printer and Option Information button.
|
|
Make sure that Duplexer Installed is displayed in the Auto Duplex Printing Information section, and then click OK.
|
|
Close the EPSON Print Utility2 dialog box.
|
|
Access the Page Setup dialog box.
|
|
Select the printer you are using as the Format for setting.
|
|
Select A4, Letter, or B5 as the Paper Size setting.
|
|
Select the appropriate Orientation setting, and click OK to close the Page Setup dialog box.
|
|
Access the Print dialog box.
|
|
Select Print Settings from the pop-up menu.
|
|
Select Rear Tray, Front Tray, or Automatic as the Paper Source setting.
|
|
Select plain papers as the Media Type setting, then select the appropriate Color and Mode settings. See online help for details on Print Settings.
|
|
Select Auto Duplex Printing Settings from the pop-up menu.
|
|
Select the Auto Duplex Printing check box.
|
|
Select the Binding edge setting.
|
|
Select one of the Select Document Type settings. This automatically adjusts Print Density and Increased Ink Drying Time.
|
Note:|
If you are printing high-density data, such as photos or graphs, we recommend making the settings in the Print Density Adjustment window.
|
|
Load paper into the rear feeder or front paper cassette, and click Print.
|